How to Replace Shark Navigator Lift-Away NV350 HEPA Filter (Step-by-Step Guide)

⏱ ~10 minutes 🔧 No special tools 🔁 Every 12 months Verified October 2026
Quick answer

Replacing the Shark Navigator Lift-Away NV350 hepa filter is a DIY job of about 10 minutes. Replace it Every 12 months under normal use. Full step-by-step below.

Compatible HEPA Filter for the Shark Navigator Lift-Away NV350

“OEM” is a genuine Shark part; the rest are tested aftermarket options.

PartType
Filter Replacement for Shark Navigator Lift Away Deluxe Professional Vacuum ZU503AMZ NV350 NV351 NV352 NV355 NV357 NV360 NV370 UV440 UV540, Parts XFF350 & XHF350, 1 HEPA + 2 Pre-Felt Filters Aftermarket Buy on Amazon
2 + 4 Pack Filters for Shark Vacuum Navigator Lift Away Filter Replacement ZU503AMZ NV350 NV351 NV352 NV355 NV356E NV357 NV360 NV370 UV440 UV540, Parts XFF350 XHF350 Aftermarket Buy on Amazon
Leadaybetter Vacuum Filter Replacement for Shark Navigator Lift Away Deluxe NV350 NV351 NV352 NV355 NV356E NV360 NV370 UV440 UV540 CU500 ZU503AMZ Models, Parts XFF350 & XHF350, 2 + 4 Pack Filters Aftermarket Buy on Amazon
Vacuum Replacement Filter for Shark Navigator Lift-Away ZU503AMZ, NV350, NV351, NV352, NV355, NV356, NV357,NV358,NV360, UV540, UV440, 2 Pre-Felt + 1 Hepa Filter Replace Part #XFF350 & XHF350 Aftermarket Buy on Amazon
Filters for Shark Navigator Lift Away Deluxe ZU503AMZ NV360 NV352 NV370 NV358 NV355 NV351 NV356E UV540 NV350 NV356, Compare to Part # XFF350 & XHF350, 2 Hepa + 4 Foam & Felt Filter Replacement Aftermarket Buy on Amazon
Filter Replacement Parts for Shark Navigator Lift-Away Vacuum ZU503AMZ CU500 NV350 NV351 NV352 NV355 NV356 NV357 NV360 NV370 NV380 NV391 UV440 UV490 UV500, 2 HEPA+4 Foam & Felt Filters Aftermarket Buy on Amazon

As an Amazon Associate we may earn from qualifying purchases. Prices and availability change; the live price is shown on Amazon.

Step-by-Step: Replacing the Shark Navigator Lift-Away NV350 HEPA Filter

1
Power off and unplug
Turn off your Shark Navigator Lift-Away NV350 and unplug it from the wall. If cordless, remove the battery pack.
2
Locate the filter compartment
Find the hepa filter housing — on most Navigator Lift-Away NV350 units it's located near the top or rear of the cyclone assembly.
3
Remove the old filter
Twist or slide out the existing hepa filter. Avoid tapping it — this releases trapped particles into the air.
4
Inspect and clean housing
Wipe the filter housing with a dry cloth. Do not use water or cleaning products inside the vacuum.
5
Insert the new filter
Align the new hepa filter with the housing guides and press firmly until it clicks into place.
6
Test suction
Plug in (or reinsert battery) and run briefly to confirm normal suction is restored.

⚠ Common mistakes to avoid

  • Confirm the part matches your exact model number before buying — Shark reuses parts across lines.
  • Never wash a filter unless it's marked washable, and dry it fully (24h) before refitting.
  • Don't force the part — if it resists, check alignment before applying pressure.
  • Always disconnect power (or remove the battery) before any internal work.
🔁 How often to replace

The Shark Navigator Lift-Away NV350 hepa filter should be replaced Every 12 months under normal use — sooner with pets or daily heavy use. Signs it's due: Reduced suction, musty odor.

How we made this page: the steps describe the standard procedure for this part type; we have not yet written a model-specific version for the Shark Navigator Lift-Away NV350; the compatible-part list comes from our own compatibility data for this model. We are not showing prices at the moment — check the current price on Amazon.