Replacing Your Shark Vertex AV2501 HEPA Filter — What You Need to Know

⏱ ~10 minutes 🔧 No special tools 🔁 Every 12 months Verified September 2026
Quick answer

Replacing the Shark Vertex AV2501 hepa filter is a DIY job of about 10 minutes. Compatible hepa filters currently start at $12.99. Replace it Every 12 months under normal use. Full step-by-step below.

Compatible HEPA Filter for the Shark Vertex AV2501

Prices pulled from Amazon and verified September 2026. “OEM” is a genuine Shark part; the rest are tested aftermarket options.

PartTypePriceRating
1 HEPA Filter & 2 Set of Foam Filters for Shark Navigator NV150 NV251 NV255 & Zero-M ZU62 ZU62C ZU60 Upright Shark Vacuum Filter Replacement Part 1238FT60 1239FT60 Aftermarket $12.99 4.85★ (858) Buy on Amazon
6Pack RVFFK950 1172FK870 Replacement HEPA Filter for Shark ION, IQ, EZ, AI Series Vacuum Cleaner RVFFK950 1172FK870 RV1001AE RV101 RV1001 AV970 AV993 RV912S AV1002AE AV753 UR1000SR AV752 by Techecook Aftermarket $13.97
$2.33/ea		 4.85★ (278) Buy on Amazon
AZ2002 Vacuum Filter Replacement Parts for Shark Vertex Duoclean Upringht Vacuum AZ2000 AZ2000W AZ2002, Compare to Part XHFAZ2000, XFFKAZ2000, 3 Filters and 6 Foam and Felt Filter. Aftermarket $19.99 4.75★ (216) Buy on Amazon
6 Pcs Replacement Pre-Motor Filter Compatible for Shark AV251WAXUS AV2511AE AV2501S AV2501AE RV2610WA UR2500SR UR250BEOUS AI Ultra Vacuum Robots Saver Kit Alternative to Part NO. XPRFRV2500 Aftermarket $13.28 4.85★ (97) Buy on Amazon

As an Amazon Associate we may earn from qualifying purchases. Prices and availability change; the live price is shown on Amazon.

Step-by-Step: Replacing the Shark Vertex AV2501 HEPA Filter

1
Power off and unplug
Turn off your Shark Vertex AV2501 and unplug it from the wall. If cordless, remove the battery pack.
2
Locate the filter compartment
Find the hepa filter housing — on most Vertex AV2501 units it's located near the top or rear of the cyclone assembly.
3
Remove the old filter
Twist or slide out the existing hepa filter. Avoid tapping it — this releases trapped particles into the air.
4
Inspect and clean housing
Wipe the filter housing with a dry cloth. Do not use water or cleaning products inside the vacuum.
5
Insert the new filter
Align the new hepa filter with the housing guides and press firmly until it clicks into place.
6
Test suction
Plug in (or reinsert battery) and run briefly to confirm normal suction is restored.

⚠ Common mistakes to avoid

  • Confirm the part matches your exact model number before buying — Shark reuses parts across lines.
  • Never wash a filter unless it's marked washable, and dry it fully (24h) before refitting.
  • Don't force the part — if it resists, check alignment before applying pressure.
  • Always disconnect power (or remove the battery) before any internal work.
🔁 How often to replace

The Shark Vertex AV2501 hepa filter should be replaced Every 12 months under normal use — sooner with pets or daily heavy use. Signs it's due: Reduced suction, musty odor.

How we made this page: the steps are written for the Shark Vertex AV2501 specifically; the compatible-part list is pulled from our parts database and price-checked against Amazon. Last verified September 2026.